Roofer Billy

??$$$$

Up

Selling My 1989 Chevy 4x4. For $18,000. Just dropped in a brand new 383 Stroker motor,with less then 1200 miles on it. Brand new exhaust manifold and headers. Brand new A/C pump,motor and seals. New power steering. New radiator, new upper and lower front ball joints. Has Ridgid rock light in each fender well. And Ridgid light bar. The Transmission and the Transfer case has been completely rebuilt. All new front brakes and rotors. And all new drums and rear brakes. Plus much more I can't remember or list. This thing runs exceptionally well and has Lots of horsepower. Truck is located in East Mesa Call Billy for more info. 480-697-seven,nine 18

It calling you. Ohh sweet child of mine... buy me.. Make me a offer.

You want this

Probably worth that in copper

4" lift and 3" body. Truck just came out of the shop and I had alot of new Goody's put in it. Runs very strong and fast. Original Stroker Motor I purchased had a oil pump issue. Stroker warrantied it. And sent me a brand new motor. So while in the shop having the motor swapped out. Stroker sent a few extra parts to Max out it's performance. Truck motor has 23 miles on it . Call or text me for more information. Also willing to trade for another vehicle. Or $ and what you have to offer.

Rewired the trailer today and put new running boards on it. Removed both wheels and bearings. Bearings were good so cleaned them up, repacked them with marine grade grease, and Installed buddy bearings. And put two new tires and rims on it. Going to make a spare tire holder ,and a step attached to the side of the front tie down and hand winch. The flex seal turned out excellent. Very curious to see how durable it is. Filled the boat with water and no leaks. I will add some pictures later. After I get the boat back on the trailer.

That's a good deal. From a good guy. 👍

Hopefully no leaks. It leaked pretty bad before. I power washed it off and scrubbed it with dawn dish soap. To remove any oil and dirt. Then flex sealed it . Going to deck the front and rear in also. And install two swivel bass seats . Like this. The decks will be done in black carpet. And a 5.5 Johnson Evenrude with a 42 # trolling motor on it. Should be a really good little boat.

This is that $600 boat now. Completely coated with 4 coats of white flex seal and 4 coats of red flex seal . And 4 coats of clear.

Nice

Good deals. That Diawa is a very nice reel. I have 3 of them and love them.

My Weatherby 270 mag. 😊.. Or my Grandmas Winchester 243 that gun don't miss.

Exactly... I've done it, pretty simple. Alot cheaper than someone else doing it.

That's beautiful

Hunt close to the town of Williams. Between Williams and Ashfork . On the north side of I 40. There is a golf coarse near catarac lake. The woods just north is a good bedding area. They lay in there until dark then move out into the golf course. Just be careful and sure your in far enough to make the 1/4 limit. The road that runs along side the railroad tracks. Is a good road to use for glassing areas .going West toward Ashfork. Around Kiabab lake is a descent area too.

Does anyone on here do small outboard motor repair? I don't know crap about them . I have a 5 horse Johnson/ Evenrude that acts like its fowling out. When you try to run it top speed . I put new plugs in it and no difference. It runs excellent idling. Any suggestions.

All over around point of the pines. They will regularly come into camp.

Exactly . It's a pain in the butt to spend all kinds of money, just to go. Then motor problems. And stuck with a trolling motor only. Not bad at Talkalai lake. But suck know matter what

Thank you. I can fix pretty much any lawn mower motor. Weed eater etc. just never a boat motor. It's a oldie but clean as a pin inside and out. 1962 Johnson/Evenrude

Damb... The bite is freaking crazy right now.

Never gotten hot has always been kept inside. Really old like my Dad but still has some good time left 😁.pumps water fine . Hmmmm

Brand new fuel line and filter. Thought maybe I lost a cylinder. Checked compression in both cylinders and all is good. It idles perfect and runs on slow setting. But when you try to give it full throttle it bogs down and acts like its loading up . running 50:1 ratio

How did everyone who went this weekend do? Dad and I fished all day yesterday for Bass. I started fishing at 6 am. And by 9 am I limited out on crappie. Dad showed up at 9:30 and We headed to the river end. And it was not a disappointment. We caught fish from 10:00 to 6:30 non stop . A average of a fish about every 20 minutes or less. No Giants. But plenty of 4,5, and even a 6.8 pound bass. Dad threw a spinner bait most the day. And a occasional Sinco on missed fish on the spinner bait. He ended up with 17 and the two biggest bass. The 6.8 and a 5.4. I threw a lucky craft red crawdad colored square billed medium size crank and never changed. Retied numerous times. But stuck with what was working. Figured if I was catching them why change. I ended the day with 13. My biggest was 4.11 . Every fish was over 2 pounds. . Caught enough Crappie to have a big fish fry. After filleting them I probably have close to 30# of fillets. Will be catch and release from now on. At least until after they spawn. Hope everyone had as good time as We have. Top water bite was great this morning.