lapazflats

Sold

Sold

Selling my hunting rig as I’ve since upgraded. I’ve had this for 10 years and regularly maintained it. It’s a Jeep so lots of parts have been changed/upgraded. Jeep is reliable. 05’ Jeep Grand Cherokee 5.7 Hemi Limited. Has the quadradrive ii (4 low) Just shy of 200k miles. Rocky Road 2” lift kit with OME shocks and springs. Tires have less than 300 miles. Upgraded Tom Woods drive shaft. I raptor lined it when I got it and it’s held up well. Seats are worn hence the seat covers. Radio needs to be finished getting installed. Needs a blend door replaced. Asking $5k OBO Located in Parker Joey 92891six779five

TTT make offer/trades welcome

BNIB. I got this several years ago with the intent of installing in my hunting rig but never did. Tons of features that may be what you’re looking for. https://www.magellangps.com/store/trx-off-road-navigators/magellan-trx7-cs-pro-dual-mount-trail-and-street-gps-navigator-with-a-camera-highlight Asking $300 OBO located in Parker. Will ship on your dime. Joey 92891six779five

TTT make offer

Sorry I never got a notification to your questions. Yes it’s blueprinted, I don’t believe it’s a PTG bolt, it is not a one piece handle.

Sold

TTT

Up for sale is a project my daughter and I started and ended up going a different route. 86’ F150 300 straight 6 manual transmission. $3500 OBO and open to firearm/optics trades. Body is in decent shape given its age. There is minor rust at bottom of doors. We put in new fuel tank, lines and pump, carb, air filter, shocks, coolant hoses, tstat, water pump, ps pump. Took the bed off and sanded frame and repainted. Next phase would have been the front half of the frame. Still have parts in boxes to be installed to include hedman header, front shocks and springs, and complete bushing kit for the truck. Truck is drivable but carb needs adjusted. I can send pics if you reach out. I plan to shuffle vehicles around on my days off and will post pics here then. Currently working nights so afternoon evenings are best. Located in Parker. Joey 9289one6779five

Bought a pair last year from cameraland and they’ve been great. Give them a call and mention you’re a member on here and they’ll take care of you. I’m no glass expert and I know everyone’s eyes are different but I prefer the color and brightness of these over my 15 scl and my previous 12 el

I’m almost positive I have one in the garage that I never used. You can have it just pay shipping. 92891677ninefive -Joey

Unfortunately needing to sell this new, never fired, Owens Armory 7 SAUM and accessories. McMillan Game Warden edge fill stock Trued/blueprinted Remington 700 short action w/ pic rail, Wyatt's internal magazine and follower and Timney HIT trigger Proof 24' Sendero contour 1.8.4 twist 3 port brake 150 Hornady A-Tip 166 grn 149 new ADG brass - 1 new ADG brass machined for modified case 54 new Remington brass 31 unknown fired count ADG brass Redding type S die set with 312 bushing Only sell as a package. $3,500.00 OBO. located in Parker. Can send more pics if needed. Feel free to text or call 92891677ninefive

Sold!

Another +1 for Walkstool. A little pricey but it’s solid and held up great for me for a couple years now. Sorry I don’t have info about the BTR, I’ve previously only used ones from like Walmart or big 5.

@cohntr6 for now I’m gonna keep it all together. If something changes I’ll let you know.

Sunday bump

Wrapping up a new build and looking for 7SAUM brass. I would prefer to purchase due to me being in Parker, but I do have reloading components to trade if necessary. 928 916 77 nine five

I was attempting to load some rounds this past weekend and when I dispensed my charge, I saw and heard my C.L. wasn't working as it normally did. Hard to put into words but the motor sounded as if it had no resistance and I saw the feed tube was spinning in a "jerking" fashion. I dumped my powder/cleaned it and tried to figure out was going on and saw the tube had backed off its threads to the motor. I tried to screw it back in to no avail. I took to the WWW and searched for a fix and saw someone else with the same issue who took theirs apart and screwed it back into place by using their finger to hold the motor from spinning. Me being frustrated and hardheaded, I did this, thus voiding the warranty, and the motor still wasn't working properly. In case this is of any use, I purchased this in December 2019. I have used Retumbo and VV565 in this unit with no issues prior. Approximately 500 rounds loaded with the C.L. This time I was using 4350. I forget what error code it shows. I don't plan on contacting RCBS for warranty knowing that I voided it. I plan on making another purchase, I just don't know whether I'll buy another CL or try a different brand. Can some of you with more reloading experience shed some light on what electronic powder measures you're using and how they're holding up? I know there's a wealth of knowledge on here and I appreciate any insight.

Sorry to all for not updating this in a timely manner. With all your input, I did contact rcbs shortly after this post and worked with a nice rep who pretty much said “how else are you supposed to fix it without doing what you did” and sent me a brand new unit very quickly. I also took the advice of making sure it’s plugged into a reputable surge protector and utilizing a beam scale to x2 weights. I have not had any issues since I received the replacement. Thanks again for the help and guidance.

I hunt these units regularly and this year has been tough. Sent you a pm with my contact info-hopefully share some info that’ll help your buddy out.

I did. A couple a great guys from the CWT community helped me get started with some brass and I ended up finding some ADG brass outa Utah. I believe it was shoot-long.com if I remember correctly. I know you can back order from creedmoorsports.com and it’ll at least get you on the list.

Bump. Duck season is around the corner.

Benelli Super Vinci 12 gauge 28” barrel. Shoots 2 3/4- 3 1/2” shells. Comes with factory chokes, case and manuals. I did “dehorn” the rear of the trigger guard since it was biting my hand. It’s a great gun I just find myself always shooting my M2. Call or text with any questions 92891677ninefive located in parker -Joey

If it’s worth it to you, I believe I have about 10-15 180 VLDH you can have to try out…just cover shipping. I’m currently working up 166 a-tip for my SAUM. Curious about your load development. 92891677ninefive Joey