lancetkenyon

Need some side by sides, but here it is mounted up. Not the rifle it will stay on, but same action and barrel. Close fit for sure. Compared to a 3-20×50 Ultra Short

Getting ready to rebuild Taylor's favorite rifle after 2300+ rounds. The 6.5SLR. I have about 430 pieces of brass already fire formed, so sticking with that cartridge. Sending 2 pcs of fired brass, 2 loaded rounds, and a resized case with 140 HVLD seated to max mag length to help in chambering the new barrel to exactly the same dimensions. New Manners PRS2 w. Gen 2 mini chassis & AI mags 22" 1:8" Proof Sendero Light Area 419 Hellfire brake R700SA will be reused with some PT&G bolt upgrades (spiral fluting/skeltonizing handle by LRI, Inc. and alloy shroud, carbon fiber knob) Cerakote in H-series Copper Brown Swapped the Kahles K624i for a S&B PMII 3-20×50 Ultra Short already. Dropping everything off at Phoenix Custom Rifles tomorrow. Hopefully have it back in a month or so to start load development. I hope to lose about 4lbs off the rifle, and make it a little more compact to carry. Losing 6" of Rem Sendero contour steel barrel length should really help in both areas.

Gathering parts for a new build (again). AxisWorks will be building it. Eric and I have already had some discussions about it. So far, I have ordered: Lone Peak Fusion TI SA w. standard .473" bolt face & nitride bolt (Titanium action weight is 23oz w. steel bolt) 4 weeks out Manner PRS2 stock in Tac Swamp w. M-5 DBM inlet for Proof Research 1.200" Sendero contour (weight should be right about 38-39oz) 4-6 weeks out. It was a flat top in stock, which should help speed up turnaround time. Getting prices on a Proof Research 6mm/.243" 1:7.5" twist @ 22-24" (42-43oz after chambering) Going to run an AxisWorks DBM set up and AI mags (10-12oz?) Probably a Trigger Tech Diamond trigger (5-6oz?) March F1 3-24x52 FML-1 (unless they finally come out with a better reticle) (24.5oz) APA Little Bastard brake (4oz) Probably swap out the bolt handle for a CF one like on my .280AI (1oz savings, but more for looks) Seekins 30mm medium (.87") rings (7-8oz) FlatlineOps level (2oz) Total weight goal: Right around 10lbs all in (unloaded) looking at these conservative numbers. Will be chambered in something like 6x47L, 6XC, 6CM, etc. I want to try and push a 105 around 3000-3100. Lone Peak Fusion TI SA action Manners PRS2 (bottom stock) But in the Tac Swamp colors like these (should look fairly similar to this rifle) Here is my CF bolt knob on my .280AI

Went today to fine tune charge weight at 200 again. Think I am pretty much done. Just need to get Taylor on a pronghorn in August now. 3 shots, 130 Hybrid OTM, 200 yards, 2868fps Need to load some up, adjust zero by .1MIL R, and go stretch it's legs.

Yes, it is shorter and also lighter by a few ounces. Once my rings get here on Monday, I will mount it up on my 6CM which is the same action as my new one I am building. I will take some side by sides next to my 3-20US.

105 Hybrid @ 3101fps. 1st round hits at (forgive me if I am off by a few yards): 437 565 1020 1498

Swapped over to a 130 Hybrid. And the rifle LOVES them! These were at 200 yards last weekend during testing.

Well, I pulled the trigger on it. Got it last night, rings should be here Monday. It should fit just fine though.

Yep! S&B PMII 5-20×50US MTC/LT DT w. H2CMR!!!

Winds were 20-25mph on Friday when we were out there.

I was 3 miles from the front on Friday at a radio site we built for MCSO. Got chased out by hot shot crews at 9:00am. It is right at the top of Fish Creek Hill.

I have a 3-20×50US too. Totally different scope body though. I appreciate the offer. Super nice of you.

10 10 10 10 10 10

More to do with quality of rifle, quality of loads, and most importantly quality of shooter than any cartridge choice. I have shot my Bushmaster AR .223 to 850 with a 90% hit rate on an 8" steel. And out to 1000 with a 70% hit rate. My brother has the same rifle, and went 0 for 10 at 850. Blamed the gun. I got behind his rifle with his ammo and went 7 for 10. That being said, I think an AR10 in .260 Rem/6.5CM even the 6.5 Grendel would be a good choice in an AR platform.

Emergency brake. I have lost brakes a time or two, and that always works for me.

That sucks. But has nothing to do with Hawkruiz69, right?

Photos? Not that I need a 5th dog...….but you never know.

Non-res are capped at a MAX of 10% of tags. Meaning that 10% does not necessarily always go to non-res applicants. Not saying you don't have a decent chance, but I wouldn't count your 100% guaranteed chickens until they hatch. Good luck in the draw. December hunts can be great. But can be tough like any other hunts. I had a buddy who drew a Dec tag in the "land of giant Coues bucks" (as he claims) last year. Bad weather knocked him out of 85% of his hunt.

Color? Photo?

3 points or less on one antler. https://dwrapps.utah.gov/huntboundary/hbstart?SP=Deer&SE=Buck&TB=true

People.complain about how.long the draw takes anyway. Going live would.take weeks. It would need to be more like Barrett Jackson. Know what lot you are hoping for, and be there at the scheduled date and time.

Ask him how he plans on getting the felons and criminals to register their guns? Once he can guarantee that, then you can reconvene the discussion.

Good deal on an awesome jacket

Best advice to give a person looking for a boat.... Don't. Rent one whenever you want to go.

As for the deer rut south of the Canyon, depends on how far south and how low. November-February.