MULEPACKHUNTER

Here's a little teaser for the live auction. RMEF Aark Machine Remington 700 6.5 PRC Remington 700 Donor Action HS Precision Stock Action trued under .0002 Upgraded oversized 8-40 Base Holes Custom Carbon Wrapped Bolt 5/16-18 Bolt knob conversion Custom Bolt Knob Bolt Face and Shaft Trued under .0002 Action Bedded to Stock Proof Carbon Barrel Barrel aligned under .0002 chambered in 6.5 PRC 5/8-24 Muzzle threads Custom Muzzle Break Turned to Barrel Diameter 20 MOA one piece scope base oversize 8-40 mounting Scope base bedded to action Timney Trigger

headed out next week, heard some good reports from 2 weeks back.

Do a little more research, it can be a short. Doesnt mean it should be but it can. Not every projectile needs to be hanging out 2 inches and 200 grns. To make it a short would kill resale so not going to happen but it was a "short" thought. I settled on the 260 almost for sure but not totally for sure.

Choosing between a few rounds for a new build and looking for resale efficacy for each. Lets say retail on this site, what bolt action rifle would sell better in your opinion? Maybe top two? All are Standard, short action. 260 REM 6.5 284 Norm 6.5 Creed 6.5x47 Lapua

not sure what you want in (pinning)? A small spot where the set screw goes is all you need. It wont move. Depending on makers some barrels have them stock and some dont. And some are misplaced depending on gas block maker. Pain in the butt. Let me know if you need it done but im far west of you.

As far as resale the idea was to build a nice rig and play for a while then sell and move on. I can do everything myself so resale will still be a profit if i can find a buyer. I have a Barrel already in 6.5 and a nice action which is why the constraints.

Ya I have some ideas on the short action 6.5 284 but it would be hand load only and its not proven. Im leaning towards the 260 rem and second the creed. Ive never shot a creed in 6.5 other than an AR10 but i always loved the 260.

Just ream some more free bore in.

Mag fit, undergassed. Where did it toss the brass? behind you? 90 degrees to the right is optimum rule, forward toss is overgassed I see alot of gas holes in barrels off to the block. After shooting pull it apart and be sure the block didnt move and look at the hole in the barrel, most times I see a figure eight shape from the gas hitting the barrel where its out of alignment.

Whats the dates?

2012 tracker pro for sale. upgraded 75 horse optimax Merc upgraded 24 volt 65 lb trolling motor upgraded sonar well kept with normal cosmetics (top of seats cracking) serviced regularly, lower unit and water pump done last year 13,000 firm

What you want to spend, I can build you one. I have a proof barrel and HS stock. Can blueprint a 700 action

He pays less percent than his secretary but he pays millions in taxes so no he doesnt pay less taxes

Anyone have any experence with PTG or other carbon sleeved Bolt?? Looking for how the wear has been after shooting for a while?

Wish it wasnt featherwieght id snag it, Carbon six carbon barrels pretty good so far.

Filson Tin is best there is, Ive had one jacket for 20 plus years and still going.

Yes

I can order them if interested, Im on west side of Surprise. They are out of stock often.

I can vouch for these breaks. I have 2 and did some testing with ballpark 60% recoil reduction on my rifle 7 PRC.

Ill have to buy a tool for it but I can do it. shoot me an email. Im on the far west side of valley. Keep in mind if it doesnt shoot well or does with that round your stuck with it. As in if it shoots well it likely wont shoot well with factory or shorter rounds Mhughes@aarkmachine.com

I use these for donor actions, stop by pawn shops..or check used section at cabellas or even gun broker has some deals if you have time to bid and track. Easier to find cheap gun than just action

How about pushing the freebore out on your current rig for the 7 mag?

ILL TAKE IT

Sale pending,